Asante EtherPaC 2000+ Series Installationsanleitung

AsantéEtherPaC 2000+ Series Plug-and-Play ISA Ethernet AdapterInstallation Guide EPaC 205-01A Book Page 1 Wednesday, October 15, 1997 3:40 PM

Page 2-4 Installing the Adapter To run the diagnostic program: 1 Insert the Driver Diskette into drive A. 2 Type the following at the DOS prompt: A:

Page 2-5 EtherPaC 2000+ Installation Guide LED Indicators Figure 2-2 shows the two LEDs that indicate Link and Activity status for installation verifi

EPaC 205-01A Book Page 6 Wednesday, October 15, 1997 3:40 PM

Page 3-13Installing Network DriversNetwork Operating Systems SupportedAfter installing, configuring and testing the adapter, you are ready to install n

Page 3-2Installing Network DriversInstalling Network Specific DriversNovell NetWare ClientTo install a NetWare DOS ODI driver automatically, run the IN

Page 3-3EtherPaC 2000+ Installation GuideNote: The EtherPaC 2000+ adapter is a Plug-and-Play module with Windows 95; no separate driver installation i

Page 3-4Installing Network Drivers4 Double-click the Network icon.5 If you have previously installed a network adapter on the computer:❏ Click Adapter

Page 4-14Remote Boot ROMBooting Your PC From a ServerYou may want to boot up your PC from a remote server on the network, or you may have a PC without

Page 4-2Remote Boot ROM4 Gently press the ROM into the socket (see Figure 4-1). Be careful not to bend the pins. Figure 4-1 Boot ROM socket on the ada

Page A-1AJumper ConfigurationThe EtherPaC 2000+ Adapter can be configured by either jumper settings or software. Please refer to the following illustrat

Copyright Notice Copyright 1996 by Asanté Technologies, Inc. All rights reserved. No part of this manual, or any associated artwork, software, produc

Page A-2Jumper ConfigurationJP1 : 1-4 (I/O ADDRESS) JP1 : 5-7 (IRQ)JP2 : BROM ADDRESS1234I/O 5 6 7 IRQ0000300H 0 0 0 2(9)0001320H 00130010340H 01040011

Page B-1BSpecificationsEtherPaC 2000+ Adapter SpecificationsBus Characteristics❏ Works in 8- or 16-bit Industry Standard Architecture (ISA) bus Standard

Page B-2Specifications❏ AUI port (optional): IEEE 802.3 10BASE-5 Thick Ethernet supported by AUI (DB15) connectorEnvironment❏ Temperature: Operating 0º

Technical SupportContacting Technical SupportTo contact Asanté Technical Support:Telephone (800) 622-7464(408) 435-0706Fax (408) 432-6018Fax-Back (800

ASANTÉ TECHNOLOGIES, INC., 821 FOX LANE, SAN JOSE, CA 95131PHONE: 408.435.8388, 800.662.9686 • FAX: 408.432.7511, APPLELINK: ASANTE.SALES, e-mail add

Page -1DRAFTCourier-Bold @ 10.0 pt 3-2, 3-5Courier-Bold @ 9.0 pt 2-4Garamond-Bold @ 10.0 pt 2-4, 3-2, 3-4–3-5Garamond-BoldItalic @ 10.0 pt 2-3, 3-3Gar

Page -2DRAFTB-1–B-2EPaC 205-01A Book Page 2 Wednesday, October 15, 1997 3:40 PM

i Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . . . . . . . . . . . . . .

ii Jumper Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . A-1Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 1-1 1 Introduction The Asanté EtherPaC 2000+ adapter is a Plug-and-Play Ethernet adapter that connects a personal computer with an Industry-Stan

Page 1-2 Introduction Features ❏ Operates in Plug-and-Play, Jumperless, or Jumper mode ❏ Support for 8- and 16-bit expansion slots ❏ Provides UTP/BN

Page 2-1 2 Installing the Adapter Using the EtherPaC 2000+ Ethernet adapter to set up your PC network, install the adapter in the computer. Note: You

Page 2-2 Installing the Adapter Optional AUI Connector An optional AUI connector is available from Asanté (see back cover). The JP3 connector on the

Page 2-3 EtherPaC 2000+ Installation Guide To set the adapter into Jumperless mode: ❏ Remove the jumper on jumper-pair 8 of JP1 (default set-ting) ❏