Asante IntraStack 6014DSB Bedienungsanleitung
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Software Asante IntraStack 6014DSB herunter. Asante IntraStack 6014DSB User`s manual Benutzerhandbuch
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
The IntraStack can be installed in a standard 19-inch equipment rack. It can also be
placed on a horizontal surface with support capabilities of 12 pounds (5.4 kilograms).
Equipment Rack Installation
To install the IntraStack in an equipment rack:
1. Place the IntraStack on a flat, stable surface.
2. Locate a rack-mounting bracket (supplied) and place it over the mounting holes
on one side of the unit, as shown below.
3. Insert six screws (supplied) into the holes and tighten with a Phillips screwdriver.
4. Repeat the two previous steps for the unit's other side.
5. Place the IntraStack in an equipment rack.
6. Secure the IntraStack by screwing its mounting brackets to the equipment rack.
To install an MII module:
The MII expansion modules are hot-swappable; you can install and or/remove a
module without turning the switch's power off.
The IntraStack's two optional Media Independent Interface (MII) expansion slots on
the switch's front panel allow for the addition of various types of media access
modules, including: 10/100TX, 100Base-FX and 10Base-FL.
The MII expansion modules are sold separately and comply with IEEE 802.1 and
802.1u specifications.
3 Install MII Expansion Modules (if any)
Desktop Placement
The IntraStack has four rubber feet on the bottom of the chassis that enable desktop/
free-standing installation of the unit.
For free-standing/desktop placement:
1. Place the IntraStack on a flat, stable, horizontal surface with a minimum area of
17.1" x 13.5" (434.3 mm x 342.9 mm) and support capabilities of 12 lbs. (5 kg.).
1 Rack Mount or Prepare for Desktop Placement
▲ Important: Make sure the switch is supported until it is secured to the equipment
rack. Failure to do so could cause the switch to fall, resulting in personal injury or
damage to the unit, or both.
Quick Installation Guide
IntraStack 6014DSB
2 Install Expansion units (if any)
Up to two expansion units can be added to the IntraStack 6014DSB, allowing up to 4
connections in a single, logical stack.
Initial expansion units for the IntraStack 6014DSB include the following:
• IntraStack 6016DSE — 16 port, 10/100TX expansion unit
• IntraStack 6008FXE — 8 port, 100Base-FX fiber expansion unit
To install an expansion unit, refer to "Installing Expansion Units" in Chapter 2 of the
IntraStack 6014DSB's User's Manual.
Overview
This guide provides instructions for mounting, installing, and configuring your IntraStack
6014DSB Ethernet switch.
This guide assumes you are familiar with installing and managing Ethernet switches. If
you are not familiar with installing and managing Ethernet switches, refer to the IntraStack
6014DSB User's Manual included in your package for more detailed instructions.
To connect the IntraStack's power cord:
1. Plug one end of the supplied power cord into
the connector on the unit's rear panel.
2. Plug the other end into a grounded AC outlet.
3. Turn the power switch to the "on" position.
The front-panel LEDs blink and the power light illuminates and remains on.
4. Turn the switch's power off.
IntraStack Front Panel
• Auto-negotiation: enabled
• Spanning Tree: enabled
• Switching mode: store-and-forward
Default Settings
The IntraStack 6014DSB is shipped with the following default configuration settings:
• IP address: 0.0.0.0
• Subnet mask: 0.0.0.0
• Default gateway: 0.0.0.0
Additional materials required:
• Network cables — refer to Step #5 ("Connect to the Network") to determine the
cables you need to connect the IntraStack to the network.
• Phillips screwdriver — for rack-mounting the IntraStack.
Package Contents
(1) MII opening bracket
(2) MII cover brackets
(1) User's Manual
(1) Quick Installation Guide (this card)
(1) IntraStack Web Browser Management
Manual Addendum
(1) Registration card
The IntraStack 6014DSB is shipped with the following items:
(1) IntraStack 6014DSB Ethernet switch
(1) Goldcard™ connector
(1) Power cord
(2) Stack-mounting pins
(2) Rack-mounting brackets
(16) Standard Phillips screws
4 Connect Power Cord
IntraStack Power Sequence
The following power-on sequence must be followed when an expansion unit is install
e
1. Power on the expansion unit(s) first.
2. Power on the IntraStack 6014DSB last.
The following power-off sequence must be followed when an expansion unit is install
1. Power off the expansion unit(s) first.
1. Remove the MII opening bracket from the front of the MII expansion slots by
unscrewing the bracket's thumbscrew.
2. Remove an MII cover bracket from the front of one of the MII expansion slots.
3. Align the bottom of an MII module with the rails on the inside of the expansion sl
4. Slide the MII module into the slot until it stops, then push the module in until it se
with the connector.
5. Repeat steps 2 - 4 to install another MII expansion module.
6. Place the MII opening bracket over the MII expansion slots.
7. Tighten the thumbscrew on the MII opening bracket's cover.
MII Opening Brack
1
2
Inhaltsverzeichnis
Seite 1 - IntraStack 6014DSB
The IntraStack can be installed in a standard 19-inch equipment rack. It can also beplaced on a horizontal surface with support capabilities of 12 po
Seite 2
5 Connect to the NetworkTo connect the IntraStack to an Ethernet network:1. Make sure the IntraStack is not powered on.2. Connect network devices to t
Weitere Dokumente für Software Asante IntraStack 6014DSB
Asante IntraStack 6014DSB Bedienungsanleitung
(146 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 5.672 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern